Black Box LPS500A-MM-LC-R3 network media converter 1000 Mbit/s 850 nm Multi-mode

Black Box LPS500A-MM-LC-R3. Maximum data transfer rate: 1000 Mbit/s, Networking standards: IEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z, Duplex system: Full. Fiber optic connector: LC, Connectivity technology: Wired. Maximum transfer distance: 21653.5" (550 m), Wavelength: 850 nm, Fiber mode structure: Multi-mode. Product color: Black. Power consumption (max): 65 W, Total Power over Ethernet (PoE) budget: 30 W
Manufacturer: Black Box
SKU: 6178152
Manufacturer part number: LPS500A-MM-LC-R3
MSRP: $455.79
$400.92
Copper port auto negotiates for network speed and features Auto MDI-X for easy cabling. LEDs indicate when it is feeding PoE power as well as when power is interrupted. RoHS compliant. Connect Gigabit-speed fiber optic to a 10-/100-/1000-Mbps copper UTP segment while also powering 802.3af devices at the end of the CAT5 run. This PoE PSE Gigabit Media Converter from Black Box enables you to transparently connect copper cabling to multimode fiber as an economical way to extend Ethernet communications well beyond the 100-meter (327-foot) CATx limit. Along with matching copper to interference-free fiber at Gigabit speeds, the converter doubles as power sourcing equipment (PSE) for Power over Ethernet (PoE) devices plugged in on the copper side. Using existing UTP cabling for both data communications and 48-VDC power simplifies a network application in terms of provisioning power and maintaining equipment. It's particularly ideal for locating equipment where electrical access is inconvenient or just too expensive to locate. Install PoE-compatible security cameras and wireless access points in areas without any nearby power outlets while reducing your overall power consumption, too. Plus, the PoE PSE Gigabit Media Converter has extensive power management features, including overcurrent protection, undercurrent detection, minimum load sensing, and PSE MDI power enable/disable. For reliable data communications, the media converter boasts link fault pass-through (LFP) capabilities, monitoring receive ports on both the fiber and copper sides for loss of signal. If signaling is lost on one media port, it automatically disables the transmit (TX) signal to the other media port. Additionally, a far-end fault (FEF) function enables the converter to cease sending a link pulse to a link partner if signaling on the fiber receive (RX) port is lost. The link partner will also synchronously stop sending data. This way, you don't lose valuable data transmitted over an invalid link
Copper port auto negotiates for network speed and features Auto MDI-X for easy cabling. LEDs indicate when it is feeding PoE power as well as when power is interrupted. RoHS compliant. Connect Gigabit-speed fiber optic to a 10-/100-/1000-Mbps copper UTP segment while also powering 802.3af devices at the end of the CAT5 run. This PoE PSE Gigabit Media Converter from Black Box enables you to transparently connect copper cabling to multimode fiber as an economical way to extend Ethernet communications well beyond the 100-meter (327-foot) CATx limit. Along with matching copper to interference-free fiber at Gigabit speeds, the converter doubles as power sourcing equipment (PSE) for Power over Ethernet (PoE) devices plugged in on the copper side. Using existing UTP cabling for both data communications and 48-VDC power simplifies a network application in terms of provisioning power and maintaining equipment. It's particularly ideal for locating equipment where electrical access is inconvenient or just too expensive to locate. Install PoE-compatible security cameras and wireless access points in areas without any nearby power outlets while reducing your overall power consumption, too. Plus, the PoE PSE Gigabit Media Converter has extensive power management features, including overcurrent protection, undercurrent detection, minimum load sensing, and PSE MDI power enable/disable. For reliable data communications, the media converter boasts link fault pass-through (LFP) capabilities, monitoring receive ports on both the fiber and copper sides for loss of signal. If signaling is lost on one media port, it automatically disables the transmit (TX) signal to the other media port. Additionally, a far-end fault (FEF) function enables the converter to cease sending a link pulse to a link partner if signaling on the fiber receive (RX) port is lost. The link partner will also synchronously stop sending data. This way, you don't lose valuable data transmitted over an invalid link
Products specifications
Attribute nameAttribute value
Width6.18"
Depth1.61"
Height0.512"
Weight21.2 oz
Harmonized System (HS) code85176990
Technical details
Product colorBlack
Flow control supportY
Ports & interfaces
Ethernet LAN (RJ-45) ports1
Connectivity technologyWired
Design
InternalN
Operational conditions
Operating temperature (T-T)-20 - 70 °C
Operating relative humidity (H-H)5 - 95 %
Operating altitude0 - 118110.2"
Power
Total Power over Ethernet (PoE) budget30 W
Power consumption (max)65 W
Features
Fiber mode structureMulti-mode
LED indicatorsY
Performance
Networking standardsIEEE 802.3, IEEE 802.3ab, IEEE 802.3af, IEEE 802.3u, IEEE 802.3x, IEEE 802.3z
Maximum transfer distance21653.5"
Duplex systemFull
Maximum data transfer rate1000 Mbit/s
Fiber optic connectorLC
Wavelength850 nm
Fiber ports quantity1
Power over Ethernet (PoE)
Power over Ethernet (PoE)Y
Product tags
  • (80699)